Microprocessor Referral Coursework 1

Microprocessor Referral Coursework 1 Task 1) Please submit a short report indicating the functionality of your application. Include in this report your program design. You should also submit your assembly file (.ASM file) so I can verify its operation in picsim. The assembly file should include comments and compile successfully using gpasm. If you do not submit this file you will automatically be awarded 0% out of 50% for the program implementation. Task 2) You should submit a short report of 2 pages or less The completed reports and flow charts should be saved as pdf files These pdf files, along with the commented source code file should be zipped and submitted via blackboard Coursework Specification Task 1) 50% for program design and implementation Create an assembly application for the pic microcontroller that will increase and decrease a program register. You should design your application using an appropriate method (flowchart/pseudo code) and then implement this on PICSIM board 1. The specification of what is required is as follows: ? You will use two buttons (RA1 and RA2) to cycle up and down the register values ? The register that will be used is PORTB (so that there is a display of the count in binary form) ? You will need to add a delay to the code so that the count can be seen. You should provide the details of any assumptions made. Task 2) 50% for report Provide a short report (maximum 2 pages including references) that answers the following question: What are the differences between the following processor instruction sets? ? RISC ? CISC Include the following aspects. ? Timing ? Number of Instructions ? Processors using each approach ? Advantages and disadvantages of each approach Marking Scheme or Guide to Assessment Criteria Task 1 50% Task 2 50% See marking grid for detailed mark allocation. 4002ELE Embedded Systems Assignment 1 (2014/15 Ref) Grade descriptors and feedback sheet for RefCW1 Student Name: Student Number: Lecturer: Outcome Below 40% 40 to 49% 50 to 59% 60 to 69% >70% Section Mark /100 Weight Weighted Mark Assembly Code Design and implementation – Does the diagram provide an accurate representation of the operational requirements? Is the diagram clear and well structured? Does the annotation of the diagram follow standards Is the code written using a formal notation. Is the code well written? Does your application meet the requirements set out in the requirements specification diagram fails to capture the requirements of the lift system. Application provides little of the required functionality, there is little structure and few comments diagram details some requirements but does not contain correct formatting. Application provides some of the functionality required. Is moderately well written. With few comments Satisfactory coverage of requirements and mostly uses correct formatting. Application code performs most of the requirements. Little formal notation and structure. All requirements are covered with satisfactory formatting. Application performs as per the requirements. Some structure and comments. Diagram presented in a professional manner. Requirements clearly covered. Formatting is accurate. Application meets the requirements is well written i.e not verbose. Makes good use of comments. 0.5 Instruction set report – Is the report well written does it address the questions posed? Discussion is missing or very limited and demonstrates that the student does not have a clear understanding of the questions Discussion is limited and demonstrates that the student has only a basic understanding of the questions Discussion is of a satisfactory standard and demonstrates that the student has a clear understanding of questions Discussion is of a high standard and demonstrates that the student has a good understanding of the questions external sources have been referenced Discussion is of an excellent standard and demonstrates that the student has a deep understanding of the questions a good range of external sources have been used. 0.5 Final Mark Comments: Please provide descriptive feedback in this section. Guide to Performance Criteria 70% and above: Your work must be of outstanding quality and fully meet the requirements of the coursework specification and learning outcomes stated. You must show independent thinking and apply this to your work showing originality and consideration of key issues. There must be evidence of wider reading on the subject. Key words which may describe a coursework at this level include: appraises, compares, concludes, contrasts, criticizes, critiques, defends, discriminates, evaluates, explains, interprets, justifies, relates, supports. 60% - 70%: Your work must be of good quality and meet the requirements of the coursework specification and learning outcomes stated. You must demonstrate some originality in your work and show this by applying new learningto the key issues of the coursework. There must be evidence of wider reading on the subject. Key words which may describe a coursework at this level include: categorizes, combines, compiles, creates, devises, generates, modifies, reconstructs, identifies, illustrates, outlines, synthesizes. 50% - 60%: Your work must be comprehensive and meet all of the requirements stated by the coursework specification and learning outcomes. You must show a good understanding of the key concepts and be able to apply them to solve the problem set by the coursework. There must be enough depth to your work to provide evidence of wider reading. Key words which may describe a coursework at this level include: demonstrates, changes, applies, operates, produces, predicts, shows, solves, uses, translates, comprehends, converts, generalizes. 40% - 50%: Your work must be of a standard that meets the requirements stated by the coursework specification and learning outcomes. You must show a reasonable level of understanding of the key concepts and principles and you must have applied this knowledge tothe coursework problem. There should be some evidence of wider reading. Key words which may describe a coursework at this level include: comprehends, defines, describes, identifies, knows, labels, lists, matches, outlines, recalls, recognizes, reproduces, selects, states, rewrites. Below 40%: Your work is of poor quality and does not meet the requirements stated by the coursework specification and learning outcomes. There is a lack of understanding of key concepts and knowledge and no evidence of wider reading. Recommended reading Ramesh S. Gaonkar, ‘Microprocessor Architecture, Programming, and Applications with the 8085’, 2002 Prentice Hall fifth edition. Fredrick M. Cady, ‘Microcontrollers and Microcomputers’, 1997 Oxford University Press, Inc. Donald P. Leach and Albert P. Malvino, ‘Digital Principles and Applications’, 1994 McGraw-Hill fifth edition. Lin, W.C.'Microprocessors: Fundamental and Applications' Douglas V. Hall 'Microprocessors and Interfacing: Programming and Hardware' Extenuating Circumstances If something serious happens that means that you will not be able to complete this assignment, you need to contact the module leader as soon as possible. There are a number of things that can be done to help, such as extensions, waivers and alternative assessments, but we can only arrange this if you tell us. To ensure that the system is not abused, you will need to provide some evidence of the problem. More guidance is available at http://www.ljmu.ac.uk/corporate/SPR/60399.htm. Any coursework submitted late without the prior agreement of the module leader will receive 0 marks Academic Misconduct The University defines Academic Misconduct as ‘any case of deliberate, premeditated cheating, collusion, plagiarism or falsification of information, in an attempt to deceive and gain an unfair advantage in assessment’. The School takes Academic Misconduct very seriously and any suspected cases will be investigated through the University’s standard policy (Academic Misconduct Policy). If you are found guilty, you may be expelled from the University with no award. It is your responsibility to ensure that you understand what constitutes Academic Misconduct and to ensure that you do not break the rules. If you are unclear about what is required, please ask. Cheating includes: (i) any form of communication with, or copying from, any other source during an examination; (ii) communicating during an examination with any person other than an authorised member of staff; (iii) introducing any written, printed or other material into an examination (including electronically stored information) other than that specified in the rubric of the examination paper; (iv) gaining access to unauthorised material in any way during or before an assessment; (v) the use of mobile phones or any other communication device during an assessment or examination; (vi) the submission of false claims of previously gained qualifications, research or experience in order to gain credit for prior learning; (vii) the falsification of research data, the presentation of another’s data as one’s own, and any other forms of misrepresentation in order to gain advantage; (viii) the submission of work for assessment that has already been submitted as all or part of the assessment for another module without the prior knowledge and consent of the Module Leader for the subsequent assessments; (ix) the submission of material purchased or commissioned from a third party, such as an essay-writing service, as one’s own. Plagiarism is defined as the representation of the work, artefacts or designs, written or otherwise, of any other person, from any source whatsoever, as the student's own. Examples of plagiarism may be as follows: i) the verbatim copying of another's work without clear identification and acknowledgement including the downloading of materials from the Internet without proper referencing of materials; ii) the paraphrasing of another's work by simply changing a few words or altering the order of presentation, without clear identification and acknowledgement; iii) the unidentified and unacknowledged quotation of phrases from another's work; iv) the deliberate and detailed presentation of another's concept as one's own. Collusion includes: (i) the conscious collaboration, without official approval, between two or more students in the preparation and production of work which is ultimately submitted by each in an identical or substantially similar form and/or is represented by each to be the product of his or her individual efforts; (ii) collusion also occurs where there is unauthorised co-operation between a student and another person in the preparation and production of work which is presented as the student's own. For more information you are directed to following the University web pages: ? Information regarding academic misconduct: http://www.ljmu.ac.uk/studysupport/81924.htm ? Information on study skills: http://www.ljmu.ac.uk/studysupport/ ? Information regarding referencing: http://www.ljmu.ac.uk/studysupport/69049.htm